Bomag BW211D-40 To BW213PD-40 Service Training Single Drum Roller 00891879

Factory Service Training For Bomag Single Drum Roller. The Bomag Service Training Manual Describes The Disassembly, Dismantling, Assembly, Installation And Repair Of Components And Assemblies. Manual Addresses The Professionally Qualified Personnel Or The After Sales Service Of Bomag, And Should Be Of Help And Assistance In Correct And Efficient Repair And Maintenance Work.

Format: PDF
Language: English
Pages: 488
Number: 00891879 (november 2010)
Bookmarks: Yes
Searchable: Yes
Wiring Diagram: Yes
Hydraulic Diagram: Yes

Model

Bomag Single Drum Roller
BW211D-40
BW212D-40
BW213D-40
BW211PD-40
BW212PD-40
BW213PD-40

S/N 101 582 42 . . . .
S/N 101 582 43 . . . .
S/N 101 582 44 . . . .
S/N 101 582 47 . . . .
S/N 101 582 48 . . . .
S/N 101 582 49 . . . .
S/N 101 582 55 . . . .
S/N 861 583 00 . . . .
S/N 101 583 02 . . . .
S/N 101 583 03 . . . .
S/N 101 583 48 . . . .
S/N 101 583 49 . . . .
S/N 101 583 50 . . . .
S/N 861 583 01 . . . .
S/N 210 583 04 . . . .

Contents

-GENERAL
Introduction
Safety Regulations
General Repair Instructions
Tightening Torques
-TECHNICAL DATA
Technical Data
-MAINTENANCE
General Notes On Maintenance
Fuels And Lubricants
Table Of Fuels And Lubricants
Running-In Instructions
Maintenance Chart
-CONNECTION OVERVIEW
Connection Overview
-TESTS AND ADJUSTMENTS
Special Tools, Tests And Adjustments
Checking The Rotation Speeds
Checking / Adjusting The Neutral Positions Of The Travel Pump
Pressure Tests In The Travel Circuit
Checking / Adjusting The Vibrator Shaft Speeds
Pressure Measurements In The Vibration Circuit
Check The Leakage Rate Of The Vibration Motor
Pressure Test In Steering Circuit
-FLUSHING AND BLEEDING
Special Tools For Flushing
Flushing – General
Flushing Schematic Travel Circuit (Distribution Travel Pump)
Flushing The Travel Circuit (Travel Pump Distribution)
Flushing Schematic Travel Circuit (Distribution Axle Motor)
Flushing The Travel Circuit (Axle Motor Distribution)
Flushing Schematic For Vibration Drive
Flushing The Vibration Circuit
Bleeding The Travel Circuit
Bleeding The Vibration Circuit
-E-PLAN WIRING DIAGRAMS
Understanding Wiring Diagrams
Circuit Symbols In The Circuit Diagram
Identification Of Switch Blocks In The Wiring Diagram
-ELECTRICS
Designation Of Components In The Wiring Diagram
Terminal Designations In Wiring Diagram
Acceleration Transducer
Battery Maintenance
Main Battery Fuse
Starting With Jump Wires
-ELECTRONIC MODULES
Operator’s Stand, Old Design
Operator’s Stand, New Design
Cabin
Fuses, Old Design
Fuses, New Design
-SPEEDOMETER MODULE
Speedometer Module
-SERVICE TRAINING
Service Training
-ENGINE
Diesel Engine, General
Service Side
Starter Side
Lubrication Oil Circuit
Oil Pressure Switch And Low Oil Pressure Circuitry
Check The Engine Oil Level
Changing Engine Oil And Oil Filter Cartridges
Coolant Circuit
Coolant Temperature Switch
Disassembling And Assembling The Coolant Temperature Switch
Replacing The Thermostat
Checking The Thermostat In Disassembled State
Check The Coolant Level
Change The Coolant
Checking The Anti-Freeze Concentration
Clean The Cooling Fins On Engine And Hydraulic Oil Cooler
Three-Phase Generator
Fuel Supply
Injection System
Injection Pump Replacement During Service
Injection Valve Replacement During Service
Checking / Repairing Injection Valves
Fuel Filter
Check, Clean The Water Separator
Change The Fuel Pre-Filter Cartridge
Change The Fuel Filter Cartridge
Checking The Compression
Check, Adjust The Valve Clearance
Boost Fuel Solenoid Valve
Engine Shut-Down Solenoid
Air Filter
-AIR CONDITIONING SYSTEM
Cleaning, Changing The Dry Air Filter Cartridge
Heating Flange On Engine
Checking The Heating Flange Control
Electric Throttle Control
Engine Monitoring
Engine
Special Tools, Deutz Engine (BFM 2012)
-DRUM
Repair Overview For Drum
-CIRCUIT DIAGRAMS
Hydraulic Diagram
Wiring Diagram

What you get

You will receive PDF file with high-quality manual on your email immediately after the payment.