Factory Shop Manual For Komatsu Forklift Truck. Manual Contains Illustrations, Instructions, Diagrams For Step By Step Remove And Install, Assembly And Disassembly, Service, Inspection, Repair, Troubleshooting, Tune-Ups.
Format: PDF
Language: English
Pages: 464
Number: BBA12E1-11 (december 2021)
Bookmarks: Yes
Searchable: Yes
Wiring Diagrams: Yes
Hydraulic Diagrams: Yes
Model
Komatsu Forklift Truck
AE50 Series
AN50 Series
FB10-12
FB10F-12
FB14-12
FB14F-12
FB15-12
FB15F-12
FB18-12
FB18F-12
FB20A-12
FB20AF-12
FB15G-12
FB15GF-12
FB18G-12
FB18GF-12
FB20AG-12
FB20AGF-12
SN 830001 And Up
FB10M-12
FB10MF-12
FB13M-12
FB13MF12
FB15-12
FB15MF-12
FB18M-12
FB18MF-12
FB20M-12
FB20MF-12
SN 825001 And Up
Contents
-FOREWORD
Section Index
-GENERAL AND SPECIFICATIONS
Outside View
Specifications
Periodic Replacement Of Consumable Parts
Safety Items For Maintenance
Standard Tightening Torque For Bolts
Standard Tightening Torque For Pipe Joints
How To Use Loctite
-TESTING AND ADJUSTING
Service Data
Method Of Releasing The Pressure In The Hydraulic Piping
Lift Interrupt Function
How To Start Up The Hour Meter
Seatbelt Interlock Function
Lifting Height Travel Speed Limit
Meter Panel
Operation Of Meter Panel
Battery
Fuse
Transfer Case
Vehicle Mounted Type Charger
Installation Type Charger
Adjustment Of Wet Type Brake And Parking Brake
Wet Type Brake
Hydraulic Oil Tank
Mast
Lifting Height Detection Sensor
Finger Bar
Naturally Descending Amount Of Hydraulic Oil Cylinder, Measurement Of Naturally Forward Tilting Amount
Air Bleeding
List Of Lubricant And Grease
-REMOVAL AND INSTALLATION
Unit Location Diagram
Unit Mass
Drawing Of Disassembly/Assembly
Mast
Lift Cylinder
Drive Axle
Steering Axle
Rear Axle
Battery
Hydraulic Pump And Pump Motor
Vehicle Mounted Charger
-DISASSEMBLY AND ASSEMBLY
Drive Axle
Transfer
Brake Wheel Cylinder
Brake Master Cylinder
Steering Gear Box
Orbitrol
Power Steering Cylinder
Steering Axle
Rear Axle
Lift Cylinder
Tilt Cylinder
Hydraulic Pump
Control Valve
Drive Motor
Pump Motor
-MAINTENANCE STANDARD
Drive Axle
Brake Master Cylinder
Steering Axle
Rear Axle
Lift Cylinder
Tilt Cylinder
Control Valve
Hydraulic Pump
Mast, Finger Bar, Fork
Drive Motor
Pump Motor
-STRUCTURE AND FUNCTION
Brake
Hydraulic Circuit Diagram
Control Valve
-TROUBLESHOOTING
Diagnosis Tool
Configuration Parts, Sensor, Unit Location Drawing
Location Drawing
Harness List
Location Of CPU Board Connector
Overview Of Abnormal Code
Preparation For Voltage Check And Current Check
Input / Output Signal Of Controller
Abnormal Code List
Diagnostic Procedure By Abnormal Code (ALA Code)
Diagnostic Procedure By Abnormal Code (ERR Code)
Diagnostic Procedure By Meter Display Trouble Code
Trouble Without Abnormal Display
Proportional Solenoid Valve Controller
Adjustment Procedure Of Tilt Automatic Horizontal (Option)
Meter Panel
-YEARLY INSPECTION CRITERIA
Motor
Control Equipment
Charge Control Unit
Battery
Power Transfer Equipment
Traveling Equipment
Steering Equipment
Braking Equipment
Cargo Handling Equipment
Hydraulic Equipment
Body, Safety Equipment, Etc
Total Test
-CONVERSION TABLE
Millimeters To Inches
Inches To Millimeters
Cubic Meters To Cubic Yards
Cubic Yards To Cubic Meters
Liter To U.S. Gallon
U.S. Gallon To Liter
Liter To U.K. Gallon
U.K. Gallon To Liter
Kilogram To Pound
Pound To Kilogram
KG/CM2 To IB/IN2
KGM To FT IB
Temperature
-APPENDIX
3BA-97-99310 (Input Cap Press-Fitting Jig)
3BA-97-99320 (Input Oil Seal Press-Fitting Jig)
3BA-97-99330 (Input Hub Bearing Press-Fitting Jig)
3BA-97-99710(Input Gear/Bearing Press-Fitting Jig)
3BA-97-99720 (Multiple Disc Alignment Jig)
3BA-97-99730 (Multiple Holder Clearance Aligning Jig)
3BA-97-99740 (3 Wheel Rear Axle Press-Fitting Jig)
3BA-97-99760 (3 Wheel Rear Axle Sensor Alignment Jig)
Service Tool Configuration
Electric Wiring Diagram (Build In Charger)
Electric Wiring Diagram (Machine With Seatbelt Interlock System And High Mast Travel Speed Limit System
Electric Wiring Diagram (Machine With Seatbelt Interlock System And High Mast Travel Speed Limit System)
Electric Wiring Diagram (Stationary Charger)
3BA-97-99310 (Input Cap Press-Fitting Jig)
3BA-97-99320 (Input Oil Seal Press-Fitting Jig)
3BA-97-99330 (Input Hub Bearing Press-Fitting Jig)
3BA-97-99710(Input Gear/Bearing Press-Fitting Jig)
3BA-97-99720 (Multiple Disc Alignment Jig)
3BA-97-99730 (Multiple Holder Clearance Aligning Jig)
3BA-97-99740 (3 Wheel Rear Axle Press-Fitting Jig)
3BA-97-99760 (3 Wheel Rear Axle Sensor Alignment Jig)
Service Tool Configuration
Electric Wiring Diagram (Build In Charger)
Electric Wiring Diagram (Machine With Seatbelt Interlock System And High Mast Travel Speed Limit System
Electric Wiring Diagram (Machine With Seatbelt Interlock System And High Mast Travel Speed Limit System)
Electric Wiring Diagram (Stationary Charger)
What you get
You will receive PDF file with high-quality manual on your email immediately after the payment.
Reviews
There are no reviews yet