Factory Shop Manual For Komatsu Bulldozer. Manual Contains Illustrations, Instructions, Diagrams For Step By Step Remove And Install, Assembly And Disassembly, Service, Inspection, Repair, Troubleshooting, Tune-Ups.

Format: PDF
Language: English
Pages: 1618
Number: SEN00986-11 (november 2007)
Bookmarks: Yes
Searchable: Yes
Wiring Diagrams: Yes
Hydraulic Diagrams: Yes

Model

Komatsu Bulldozer
D375A-5E0
SN 50001 And Up

Contents

-INDEX AND FOREWORD
Index
Foreword And General Information
-SPECIFICATION
Specification Drawing
Specifications
Weight Table
Table Of Fuel, Coolant And Lubricants
-STRUCTURE, FUNCTION AND MAINTENANCE STANDARD
Engine And Cooling System
Power Train
Undercarriage And Frame
Hydraulic System
Work Equipment
Cab And Its Attachments
Electrical System
-STANDARD VALUE TABLE
Standard Value Table For Engine
Standard Value Table For Machine
-TESTING AND ADJUSTING
Tools For Testing, Adjusting, And Troubleshooting
Testing Engine Speed
Testing Intake Air Pressure (Boost Pressure)
Testing Exhaust Temperature
Testing Exhaust Gas Color
Adjusting Valve Clearance
Testing Compression Pressure
Testing Blow-By Pressure
Testing Engine Oil Pressure
Testing EGR Valve And Bypass Valve Drive Oil Pressure
Handling Of Fuel System Devices
Releasing Residual Pressure From Fuel System
Testing Fuel Pressure
Handling Of Reduced Cylinder Mode Operation
Handling Of No Injection Cranking Operation
Testing Leakage From Pressure Limiter And Return Rate From Injector
Bleeding Air From Fuel Circuit
Testing Fuel Circuit For Leakage
Handling Controller Voltage Circuit
Replacing And Adjusting Alternator And Air Conditioner Compressor Belt
Testing Fan Motor Speed
Testing Fan Circuit Oil Pressure
Bleeding Air From Fan Pump
Adjusting Fuel Control Dial And Decelerator Pedal
Testing Power Train Oil Pressure
Adjusting Transmission Speed Sensor
Simple Procedure For Testing Brake Performance
Adjusting Brake Pedal And Parking Brake Lever
Adjusting Position Of PCCS Lever Console
Emergency Escape Method When There Is Failure In Power Train
Inspecting Wear Of Sprocket
Testing And Adjusting Track Shoe Tension
Testing Work Equipment Oil Pressure
Testing Control Circuit Main Pressure
Testing PPC Valve Output Pressure
Adjusting Play Of PPC Valve
Testing Output Pressure Of Ripper Pin-Puller Solenoid Valve
Checking Location Of Cause Of Hydraulic Drift Of Blade And Ripper
Testing Leakage Inside Work Equipment Cylinder
Releasing Remaining Pressure In Work Equipment Cylinders
Bleeding Air From Work Equipment Cylinders
Adjusting Ripper Lever Position
Adjusting Work Equipment Lock Lever
Testing And Adjusting Operator’s Cab
Adjusting Blade
Special Functions Of Monitor Panel (EMMS)
Adjustment Method When Controller Has Been Replaced
Preparation Work For Troubleshooting For Electrical Equipment System
Inspection Procedure Of Diode
Handling Of Optional Devices
Request For Opening ORBCOMM Terminal
Initialization Procedures For VHMS Controller
Using Method Of Komtrax Functions Of ORBCOMM Terminal
Precautions For Replacing VHMS Controller
PM Clinic Service
-TROUBLESHOOTING
Failure Code Table And Fuse Locations
General Information On Troubleshooting
Troubleshooting By Failure Code
Troubleshooting Of Electrical System (E-Mode)
Troubleshooting Of Hydraulic And Mechanical System (H-Mode)
Troubleshooting Of Engine (S-Mode)
-DISASSEMBLY AND ASSEMBLY
General Information On Disassembly And Assembly
Engine And Cooling System
Engine
Power Train
Undercarriage And Frame
Hydraulic System
Work Equipment
Cab And Its Attachments
Electrical System
-DIAGRAMS AND DRAWINGS
Hydraulic Diagrams And Drawings
Electrical Diagrams And Drawings