Tigercat 880 Service Manual Logger 36953AENG

$29.00

Factory Service Manual For Tigercat Logger. Manual Contains Illustrations, Instructions, Diagrams For Step By Step Remove And Install, Assembly And Disassembly, Service, Inspection, Repair, Troubleshooting, Tune-Ups.

Format: PDF
Language: English
Pages: 520
Number: 36953AENG (may 2014)
Bookmarks
Searchable
Wiring Diagrams
Hydraulic Diagrams

Model

Tigercat Logger
880
Serial Number 8800101 To 8800500

Contents

STANDARDS, ROPS, FOPS, OPS, TOPS
NON-APPROVED FIELD PRODUCT CHANGES
INTRODUCTION
-SAFETY
Avoid Injury From Backover Accidents
Battery Disconnect Switch
Battery Safety
Cab Electrical Compartment
Cab Exits
Chain Shot
Cooling System
Emergency Cab Exits
Emergency Escape Hatch
Engine Doors
Exhaust Fumes
Felling Trees
Fire Prevention
Fluid Injection Injury
Fluid Leaks
General Safety Precautions
Grease Gun, Using
Grease Injection Injury
Harvesting Attachment – General Safety
Harvesting Head Service
Hazard Zone
Hydraulic Pressure Hazard
Interclock Switch, Safety
Lightning Safety Awareness
Liquid Staring Aid
Loose Clothing Hazard
Notice Labels
Operating Safety Precautions
Parking Hazards
Parking The Machine
Pneumatic Grease Guns, Using
Pressurized Hydraulic Tank
Protective Clothing
Rear Door
Safety Hazards – Operating
Safety Hazards – Viton Seals
Safety Interlock Switches On Cab Doors
Safety Labels
Safety Precautions General
Safety Precautions, Operating
Safety Precautions, Servicing
Safety Symbols
Seat Belt
Side Window
Signal Words
Signal Words
Welding, Prior To
Working With Oil
-LUBRICATION & MAINTENANCE
Air Cleaner Maintenance
Air Conditioning System Checking The System
Case Drain Strainers
Checking The Air Conditioning System
Emergency Exits Check Monthly
Filters
Fire Prevention
Fuel – Refueling Procedure
Fuel Tank
Fuel Tank Shut-Off Valves
Fuel Tank Strainer
Hydraulic Oil Filters
Hydraulic Tank Pressurization Instructions
New Machine Maintenance
Oil Analysis Program
Pressure And Speed Settings
Pressure Setting Procedures
Preventive Maintenance Schedule
Refueling Procedure
Scheduled Maintenance
Swing Drive Lubrication
Torque Chart
Torque Chart General
Torque Fluid Connections
Track Components
Track Operation And Wear Prevention
-HYDRAULIC SYSTEM
Case Drain Strainers
Circuit Diagram
Filter
Hand Fill Pump
Hydraulic Pumps
Hydraulic System Operation
Hydraulic Tank
Hydraulic Tank Vacuum Installation
Load Sensing
Main Control Valve/Manifold
Schematic Diagrams
-PILOT SYSTEM
Accumulator
Charging The Accumulator
Circuit Diagram
Electrical Circuit
Pilot System Components
Pilot System Schematic
-ELECTRICAL AND COMPUTERS
Battery Compartment
Channels
Computer
Connect To The Md3 With IQANRUN 2
Control Adjustment Settings
Diagnostic Breakout Harnesses
Downloading Applications From Dealer Website
Electrical Box – Main
Electrical Compartment – Cab
Electrical Installation – Cab
Electrical Kit – Service And Diagnostics
Electrical Schematic
Engine Fault Code Messages – Alert
Engine Fault Code Messages – Critical
Fuses And Relays
Fuses And Relays – Cab
Fuses And Relays – Electrical Box
Hydraulics Adjustment Settings Reference Chart
ID-Tag
Input And Output Channels
IQAN Modules
IQANRUN 2
IQAN Software
MD3 Computer
MD3 Computer Main Menu
MD3 Display Module Schematic
Servicing The Md3 With IQANRUN 2
Switch And Sensor Locations
Troubleshooting Diagnostic Breakout Harnesses
Update Application
Wire Colour Code Chart
Xa2-A0 Engine Frame Module Schematic
Xa2-A1 Engine Frame Module Schematic
Xs2-A0 Cab Module Schematic
-ENGINE START AND STOP
Engine Cold Weather Starting
Engine, Starting
Engine, Stopping
Schematic Diagram
-ENGINE ANTI-STALL
Anti-Stall
Circuit Diagram
Computer Control System Components
Schematic Diagrams
-OIL COOLER, RADIATOR, CHARGE AIR COOLER AND FAN
Charge Air Cooler
Circuit Description
Circuit Diagram
Fan Circuit Hydraulic Schematic
Fan Drive Control Valve
Fan Motor
Fan Pump
Fan Pump / (Max) Maximum Pressure
Fan Speed Checks
Filter
Hydraulic Oil Reservoir
Oil Cooler
Radiator
Radiator Cooling System
Standby Pressure
-TRACK DRIVE
Drive System Pressure Settings
Hydrostatic Drive System
Important Track Drive Notes
Motor Start-Up Procedure
Set Straight Travel
Torquing Undercarriage Bolts
Track Components
Track Speed Set-Up Procedure
Track Timing Chart
Wear Limits
-BOOM FUNCTIONS
Adjust Oil Flow To Cylinders (Cylinder Cycle Times)
Boom Component Lubrication
Boom Control Valve
Boom System Description
Load SensingEngine Anti-Stall
Setting Port Relief Valves
-SWING
Adjust Swing Bearing Backlash
Circuit Description
Hydraulic Schematic
Pressure And Swing Speed Settings
Swing Bearing Replacement
Swing Bearing Wear Limits
Swing Drive Components
Swing Drive Lubrication
-LOADER GRAPPLE BUTT ‘N‘ TOP/POWER CLAM
Attachment Installation
Butt N Top Grapple
Circuit Diagram
Computer Control System
Grapple Control And Tilt Float Options
Hydraulic Schematic
Hydraulic Tank Pressurization Instructions
Loader Butt N Top/Power Clam System
Md3 Electronic Adjustment Procedure
Oil Flow Cycle Times, Adjust
Power Clam Grapple
Pressure Settings Attachment, Pump
Setting Main Control Valve Port Relief Valves
-LOADER LIVE HEEL (SHOVEL LOGGER)
Adjust Oil Flow – Cycle Times
Loader Live Heel System
Setting Port Relief Valves
-HARVESTER
Attachment Circuit Description
Circuit Diagram
Electrical Schematic
Harvesting Head Installation
Head Rotate Circuit Description
Hydraulic Schematic
Loader Harvester System
Main Control Valve Port Relief Pressure Settings
Pump 1 And Pump 1 Control Valve Pressure Settings
Setting Cycle Times
-CAB TILT
Cab Tilt Cylinder Replacement, Bleeding And Filling Procedure
Cab Tilt Hydraulic Schematic
Cab Tilt Hydraulic System
Cab Tilt Pressure Settings
Cab Tilt Switch
Operating The Hand Pump
Power Roof And Right Door Manual Operation – Hand Pump
-MISCELLANEOUS
Installation Parts Information
Removal Of Windows
Window Installation
Window Replacement