Factory Service Manual For Bomag Road Finisher. Manual Contains Illustrations, Instructions, Diagrams For Step By Step Remove And Install, Assembly And Disassembly, Service, Inspection, Repair, Troubleshooting, Tune-Ups.
Format: PDF
Language: ENG
Pages: 778
Number: 00892122 (october 2012)
Bookmarks: Yes
Searchable: Yes
Wiring Diagrams: Yes
Hydraulic Diagrams: Yes
Model
Bomag Road Finisher
BF600C – HSE
BF600C – HCE
S/N 821 837 85…
S/N 821 837 86…
S/N 821 837 89…
S/N 821 837 90…
Contents
-GENERAL
Introduction
Safety Regulations
General Repair Instructions
Tightening Torques
-TECHNICAL DATA
Technical Data
-MAINTENANCE
General Notes On Maintenance
Fuels And Lubricants
Table Of Fuels And Lubricants
Running-In Instructions
Maintenance Table
-FUNDAMENTAL ELECTRICS
Understanding Wiring Diagrams
Circuit Symbols In The Circuit Diagram
Battery Ground And Analog Ground
Processor Signals
Current And Voltage
Pulse Width Modulation (PWM)
Resistance
Series / Parallel Connection
Ohm’s Law
Electrical Energy
Formula Diagram
Metrology
Diodes, Relays, Fuses
Inductive Proximity Switches
Plug Connectors
Magnetic Coil Plug
Deutsch Plug, Series DT And DTM
Plugs And Terminals In Spring Clamping Technology
Batteries
Battery Maintenance
Starting With Jump Wires
Main Battery Switch
Fuses
Replace Heating Elements
Failure Codes, Sauer Controller
-ENGINE ELECTRICS
Installation Location For Engine Control Unit
EMR3 System Components
Pin Assignment Of Engine Control Edc16 / EMR3
Camshaft Speed Sensor
Crankshaft Speed Sensor
Rail Pressure Sensor
Fuel Pressure Sensor
Fuel Control Unit FCU
Injectors
Oil Pressure Sensor
Charge Air Temperature – Charge Air Pressure Sensor
EMR Coolant Temperature Sensor
Glow Plugs
Sensor, Water In Fuel, C39
Air Filter Vacuum Switch, C40
Level Probe Coolant Tank, C38
Diagnostics Interface
Diagnose With Can-Bus
Diagnose With Serdia
Fault Code Indication, Diesel Engine
EMR3 List Of Fault Codes
Generator
Electric Starter
-ENGINE
Diesel Engine
Engine Description TCD 2013, 4 And 6 Cylinder
Lubrication Oil Circuit TCD 2012 / 2013
Coolant Circuit TCD 2012 / 2013
Fuel System TCD 2012 / 2013
Deutz Common Rail (DCR) Injection System For TCD 2012 / 2013
Exhaust Gas Recirculation TCD 2012 / 2013
Wastegate – Charge Pressure Controller On TCD-Engines
Engine Problems
Check The Engine Oil Level
Changing Engine Oil And Oil Filter Cartridge
Replace The Fuel Filter Cartridges
Changing The Fuel Filter, Bleeding The Fuel System
Check, Clean The Water Separator
Check The Coolant Level
Replacing The Coolant
Air Filter Maintenance
Adjust The Valve Clearance
Adjusting The Control Piston Play
Clean The Cooling Fins On Engine And Hydraulic Oil Cooler
Check The Engine Mounts
Replace The Crank Case Ventilation Valve
Electronic Injector Test EMR
Engine Conservation
Checking The Condition And Tension Of The Screed Heating Generator V-Belt, Tensioning And If Necessary Replacing The V-Belt
Check, Tension, Replace The V-Belt
Special Tools, Deutz Engine (TCD 2013 2V)
-HYDRAULICS
Hydraulic Circuit
Travel System
Actuator Drive
Scraper Chain Drive
Vibration And Tamper Drive
Fan Drive
-TESTS AND ADJUSTMENTS
Checking And Adjusting The Vibration
Checking And Adjusting The Tamping Process
Checking/Adjusting The Mobile Screed
Checking/Adjusting The Hopper Wings
Checking & Adjusting The Time For Screed Levelling
-CENTRAL LUBRICATION SYSTEM
BF 600C With HC Screed, 32 Lubrication Points
BF 600C With HC Screed, 34 Lubrication Points
Filling The Lubricant Container
Electric Pump
Integrated Electronic Control
Progressive Distributor
Fault – Cause – Remedy
Repair Of A Blocked Distributor
-SUPPLIERS DOCUMENTATION
Travel Pump
Travel Motor
Conveyor Screws – Scraper Belt Motor
Travel Gear
-CIRCUIT DIAGRAMS
Hydraulic Diagram
Wiring Diagram
What you get
You will receive PDF file with high-quality manual on your email immediately after the payment.
Reviews
There are no reviews yet.