Factory Technical Manual For John Deere Loader. Manual Contains Illustrations, Instructions, Diagrams For Step By Step Remove And Install, Assembly And Disassembly, Service, Inspection, Repair, Troubleshooting, Tune-Ups.

Format: PDF
Language: English
Pages: 247
Issued: august 1997
Hydraulic Diagrams: Yes

Model

John Deere Cameco Loader
SP1800B

Contents

-SAFETY
Safety And You
Operation Safety
Service Safety
Safety In Your Service Area
Safety When Cleaning Or Storing
Safety Nevers
Recognizing Safety Information
Understanding Signal Words
Follow Safety Instructions
Protect Bystanders
Use Hand Holds And Steps
Prevent Machine Runaway
Avoid Exhaust Fumes
Keep Riders Off Machine
Handle Fuel Safely-Avoid Fires
Safely Service Accumulators
Safely Service Cooling System
Prepare For Emergencies
Wear Protective Clothing
Use Safety Lights And Devices
Use Cylinder Safety Stops
Practice Safe Maintenance
Avoid High Pressure Fluids
Use Caution On Hillsides
Stopping And Parking
Service Tires Safely
Fire Prevention
-SPECIFICATIONS
Engine And Drivetrain
Hydraulic Pumps
Hydrostatic Transmission
General Hydraulics
Pressure Settings
Hydraulic Schematic (Grab & Lift)
Hydraulic Schematic (Steer, Swing, Flex)
-CAPACITIES
Engine
Radiator
Transmission
Rear Steering Axle
Front Rigid Axle
Brake Fluid
Hydraulic Tank
Diesel Fuel
Torques (Dry)
Tire Inflation Pressure
Pump Drive
-TORQUE SPECIFICATIONS
SAE Bolt And Nuts
SI (Metric) Bolts And Nuts
Conversion Tables
-GENERAL INFORMATION
Introduction
Diagnostic Section
Troubleshooting Tools
Troubleshooting
Visually Inspect Hydraulic System
Hydraulic System Testing Precautions
Visually Inspect Electrical System
Electrical System Testing Precautions
Service Supplies
Service Tools
Hydraulic Symbols
Miscellaneous Symbols
Methods Of Operation
Electrical Symbols
-SERVICE POINTS
Initial Start Up
First 50 Hours Of Operation
Every 10 Hours Of Operation (Daily)
Every 70 Hours Of Operation
140 Hours – 2 Weeks Of Operation
250 Hours – Monthly Operation
500 Hours – 2 Months Of Operation
1000 Hours – 4 Months Of Operation
As Necessary
-HYDROSTATIC SYSTEM
The System Circuit
Theory Of Operation
Initial Start Up Procedure
Fluid And Filter Maintenance
Troubleshooting
Hydrostatic Pump
Minor Repair
Major Repair
Neutral Start/Run Solenoid Valve
Front Axle Motor-Fixed
-MAIN HYDRAULIC SYSTEM
Contamination Control
Hydraulic Oil
Troubleshooting
Diagnosis Of Hyd. System Malfunctions
Diagnosis Of Hyd. Components
Double Vane Pump
Directional Control Valve
Hydraulic Cylinder Repair
Relief Valve
-STEERING SYSTEM
Priority Valve
Steering Valve
-TRANSMISSION
Drawing
Disassembly
Shifter Assy
Output Shaft
Third Stage Shaft Removal
Remove Input Shaft
Second Stage Shaft
Clean and Inspect
Assembly
Output Shaft
Install Second Stage Shaft
Install Input Shaft
Third Stage Shaft
Shifter Assy Installation
Install Transmission on Loader
-AXLE REPAIR
Front Rigid Axle
Rear Steering Axle
-ELECTRICAL SYSTEM
Visually Inspect Electrical System
Safety Precautions
Specifications
Theory Of Operation
Cleaning Battery Post
Jumping The Battery
Charging The Battery
Precautions For Alternator
Inspection
Common Circuits
Operational Checks
Electrical Malfunctions
Oil Pressure Sender
Oil Pressure Switch
Engine Coolant Temp Gauge Sender
Engine Coolant Temp Switch
Hydraulic Oil Temperature Sender
Fuel Sending Unit
Hydraulic Filter Pressure Switch
Air Filter Restriction Switch